The effect of differently sized Ag catalysts on the fabrication of a silicon nanowire array using Ag-assisted electroless etching

A simple and low cost method to generate single-crystalline, well-aligned silicon nanowires (SiNWs) of large area, using Ag-assisted electroless etching, is presented and the effect of differently sized Ag catalysts on the fabrication of SiNWs arrays is investigated. The experimental results show that the size of the Ag catalysts can be controlled by adjusting the pre-deposition time in the AgNO₃/HF solution. The optimum pre-deposition time for the fabrication of a SiNWs array is 3 min (about 162.04 ± 38.53 nm Ag catalyst size). Ag catalysts with smaller sizes were formed in a shorter pre-deposition time (0.5 min), which induced the formation of silicon holes. In contrast, a large amount of Ag dendrites were formed on the silicon substrate, after a longer pre-deposition time (4 min). The existence of these Ag dendrites is disadvantageous to the fabrication of SiNWs. Therefore, a proper pre-deposition time for the Ag catalyst is beneficial to the formation of SiNWs.SiNWs were synthesized in the H₂O₂/HF solution system for different periods of time, using Ag-assisted electroless etching (pre-deposition of the Ag catalyst for 3 min). The length of the SiNWs increases linearly with immersion time. From TEM, SAED and HRTEM analysis, the axial orientation of the SiNWs is identified to be along the [001] direction, which is the same as that of the initial Si wafer. The use of HF may induce Si–H_x bonds onto the SiNW array surface. Overall, the Ag-assisted electroless etching technique has advantages, such as low temperature, operation without the need for high energy and the lack of a need for catalysts or dopants.     

Mesogenic and optical properties of α,α′‐bis(4‐alkoxyphenylethynyl)oligothiophenes

Liquid crystalline α,α′‐bis(4‐alkoxyphenylethynyl)oligothiophenes (bi‐ and ter‐thiophene) have been synthesized and their mesogenic behaviour and optical properties investigated. They all exhibited a nematic mesophase, and compounds with long alkoxy chains also showed lamellar phases. Increasing the number of thiophene units increased both the transition temperatures and the mesophase ranges. As for their optical properties, incorporating more thiophene units results in red‐shifted absorption and emission spectra, slightly enhanced quantum efficiency, and a larger Stoke's shift. Most importantly, in terms of the absorption and emission maxima, the incorporation of one 4‐alkoxyphenylethynyl moiety was found to be equivalent to adding one thiophene ring.     

Synthesis and Application of Epoxidized Natural Rubber

Abstract

North Vietnamese NR latexes were successfully epoxidized using peracetic acid at moderate temperature and pH range. The epoxide contents of pure epoxidized natural rubber (ENR) are from 5 to 70 mol%. The ENR products were characterized and determined by spectral and thermal analysis besides the chemical titration. Conditions of longlasting or excessive temperature, or high acidic pH led to side ring opened products, proved easily by IR, ¹H-NMR, and DSC analysis. The ENR were vulcanized using a semiefficient system. The epoxidation increased the adhesion between rubber and tire cord and metal. This effect becomes stronger beyond 25 mol% and tends to be limited at over 60 mol%. The ENRs were used to formulate special-purpose adhesives. The shear strength of the adhesive ranges from 32 to 45 kg/cm² for bonding rubber to nylon and rubber to metal, respectively.     

Deprotection‐free preparation of propargyl ether‐containing phosphinated benzoxazine and the structure–property relationship of the resulting thermosets

Generally, protection and deprotection procedures of amino groups are required in preparing propargyl ether‐containing benzoxazines. In this study, we report a facile, deprotection‐free preparation of a propargyl ether‐containing phosphinated benzoxazine (2) from the nucleophilic substitution of a phenolic OH‐containing phosphinated benzoxazine (1) and propargyl bromide in the catalysis of potassium carbonate. The structure of (2) was characterized and confirmed by a high‐resolution mass spectrum, ¹H, ¹³C, ¹H‐¹H, ¹H‐¹³C nuclear magnetic resonance (NMR) spectra, and X‐ray single crystal diffractogram. infrared (IR) and differential scanning calorimetry were used to monitor the ring‐opening of benzoxazine and crosslinking of propargyl ether. The microstructure and the structure–property relationship of the resulting homopolymers and copolymers are discussed. The T_g of homopolymer of (2) is 208 °C by dynamic mechanical analysis, the coefficient of thermal expansion is 43 ppm/°C, and T_d 5% (N₂) is 393 °C, respectively, which are higher than those of the homopolymer of (1) . Similar trends were observed in the copolymerization system. The results demonstrate the beneficial effect of crosslinking afforded by the propargyl ether group is higher than that by the phenolic OH group. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Critical values for higher rank numerical ranges associated with roulette curves

In this paper the critical value is determined for the higher rank numerical ranges of matrices associated with a parameter of roulette curves, for which the higher rank numerical range is a regular polygon for every parameter less than or equal to the critical value.     

A Hydrosilylation Approach to Silicon‐Bridged Functional Dipyrromethanes: Introducing Silicon to A New Arena

Two silylene‐spaced ((E)‐vinylsilyl)anthracene‐dipyrromethane dyads have been designed and synthesized by RhCl(PPh₃)₃‐catalyzed hydrosilylation reactions of 5‐methyl‐5′‐(ethynylaryl)dipyrromethanes with (9‐Anthryl)‐dimethylsilane. The complexation studies of dyads toward different anions have also been performed, which reveal that dyads exhibit a highly selective response towards fluoride anion attributable to both hydrogen‐bonding and pentacoordination phenomena. This dual‐mode fluoride recognition event is unprecedented and may pave the way for future developments in the areas of porphyrinoids, organosilicon, polymer, and supramolecular chemistry.     

Investigation of entrance effects on particle electrophoretic behavior near a nanopore for resistive pulse sensing

Resistive pulse sensing using solid-state nanopores provides a unique platform for detecting the structure and concentration of molecules of different types of analytes in an electrolyte solution. The capture of an entity into a nanopore is subject not only to the electrostatic force but also the effect of electroosmotic flow originating from the charged nanopore surface. In this study, we theoretically analyze spherical particle electrophoretic behavior near the entrance of a charged nanopore. By investigating the effects of pore size, particle–pore distance, and salt concentration on particle velocity, we summarize dominant mechanisms governing particle behavior for a range of conditions. In the literature, the Helmholtz–Smoluchowski equation is often adopted to evaluate particle translocation by considering the zeta potential difference between the particle and nanopore surfaces. We point out that, due to the difference of the electric field inside and outside the nanopore and the influence from the existence of the particle itself, the zeta potential of the particle, however, needs to be at least 30% higher than that of the nanopore to allow the particle to enter into the nanopore when its velocity is close to zero. Accordingly, we summarize the effective salt concentrations that enable successful particle capture and detection for different pore sizes, offering direct guidance for nanopore applications.